Рубрики
Android

BlueBox commands

List of Access Point CLI commands:
 config wlan                        -- config wlanX
 connect bss                        -- connect to bssX
 del acl                            -- Delete Access Control List
 del wdsacl                         -- Delete WDS Access Control List
 del key                            -- Delete Encryption key
 find bss                           -- Find BSS
 find all                           -- Find All BSS
 dhcps help                         -- Display DHCP Server Command Help
 get 11gonly                        -- Display 11g Only Allowed
 get 11goptimize                    -- Display 11g Optimization Level
 get acl                            -- Display Access Control List
 get wdsacl                         -- Display WDS Access Control List
 get wdsap                          -- Display WDS Access Point
 get apmode                         -- Display AP Mode(runtime)
 get aging                          -- Display Aging Interval
 get antenna                        -- Display Antenna Diversity
 get association                    -- Display Association Table
 get authentication                 -- Display Authentication Type
 get basisconnect                   -- Display Basis of Connect Mode
 get beaconinterval                 -- Display Beacon Interval
 get burstSeqThreshold              -- Display Max Number of frames in a Burst
 get burstTime                      -- Display Burst Time
 get bridgelearning                 -- Get bridge learning status
 get calibration                    -- Display Noise And Offset Calibration Mode
 get cckTrigHigh                    -- Display Higher Trigger Threshold for CCK Phy Errors for ANI Control
 get cckTrigLow                     -- Display Lower Trigger Threshold for CCK Phy Errors for ANI Control
 get cckWeakSigThr                  -- Display ANI Parameter for CCK Weak Signal Detection Threshold
 get cipher                         -- Display Encryption cipher
 get config                         -- Display Current AP Configuration
 get countrycode                    -- Display Country Code
 get ctsmode                        -- Display CTS mode
 get ctsrate                        -- Display CTS rate
 get ctstype                        -- Display CTS type
 get dhcpc                          -- Display DHCP Clinet State
 get domainsuffix                   -- Display Domain Name Server suffix
 get dtim                           -- Display Data Beacon Rate (DTIM)
 get enableANI                      -- Display Adaptive Noise Immunity Control On/Off
 get encryption                     -- Display Encryption Mode
 get eth2wlan                       -- Display Eth2Wlan Broadcast packet filter state
 get puregmode                      -- Display Pureg Mode
 get firStepLvl                     -- Display ANI Parameter for FirStepLevel
 get fragmentthreshold              -- Display Fragment Threshold
 get frequency                      -- Display Radio Frequency (MHz)
 get gateway                        -- Display Gateway IP Address
 get groupkeyupdate                 -- Display Group Key Update Interval (in Seconds)
 get hardware                       -- Display Hardware Revisions
 get hostipaddr                     -- Display Host IP Address
 get ipaddr                         -- Display IP Address
 get ipmask                         -- Display IP Subnet Mask
 get key                            -- Display Encryption Key
 get keyentrymethod                 -- Display Encyrption Key Entry Method
 get keysource                      -- Display Source Of Encryption Keys
 get login                          -- Display Login User Name
 get macaddress                     -- Display Mac address
 get nameaddr                       -- Display IP address of name server
 get nf                             -- Display Noise Floor
 get noiseImmunityLvl               -- Display ANI Parameter for Noise Immunity Level
 get ofdmTrigHigh                   -- Display Higher Trigger Threshold for OFDM Phy Errors for ANI Control
 get ofdmTrigLow                    -- Display Lower Trigger Threshold for OFDM Phy Errors for ANI Control
 get ofdmWeakSigDet                 -- Display ANI Parameter for OFDM Weak Signal Detection
 get quietAckCtsAllow               -- Display if Ack/Cts frames are allowed during quiet period
 get quietDuration                  -- Display Duration of quiet period
 get quietOffset                    -- Display Offset of quiet period into the beacon period
 get radiusname                     -- Display RADIUS server name or IP address
 get radiusport                     -- Display RADIUS port number
 get rate                           -- Display Data Rate
 get hwtxretries                    -- Display HW Transmit Retry Limit
 get swtxretries                    -- Display SW Transmit Retry Limit
 get rtsthreshold                   -- Display RTS/CTS Threshold
 get shortpreamble                  -- Display Short Preamble Usage
 get shortslottime                  -- Display Short Slot Time Usage
 get sntpserver                     -- Display SNTP/NTP Server IP Address
 get softwareretry                  -- Display Software Retry
 get spurImmunityLvl                -- Display ANI Parameter for Spur Immunity Level
 get ssid                           -- Display Service Set ID
 get ssidsuppress                   -- Display SSID Suppress Mode
 get station                        -- Display Station Status
 get SuperG                         -- Display SuperG Feature Status
 get systemname                     -- Display Access Point System Name
 get sta2sta                        -- Display wireless STAs to wireless STAs connect state
 get eth2sta                        -- Display ethernet to wireless STAs connect state
 get telnet                         -- Display Telnet Mode
 get timeout                        -- Display Telnet Timeout
 get matinfo                        -- Display MAT Information
 get matstate                       -- Get MAT Status
 get syslog                         -- Display Syslog Information
 get tzone                          -- Display Time Zone Setting
 get uptime                         -- Display UpTime
 get wds                            -- Display WDS Mode
 get wirelessmode                   -- Display Wireless LAN Mode
 get wpaie                          -- Display current IE of WPA
 get wlanstate                      -- Display wlan state
 get rbcnt                          -- Reset reboot counter
 help                               -- Display CLI Command List
 rxstat                             -- RD state
 ping                               -- Ping
 reboot                             -- Reboot Access Point
 quit                               -- Logoff
 set 11gonly                        -- Set 11g Only Allowed
 set 11goptimize                    -- Set 11g Optimization Level
 set acl                            -- Set Access Control List
 set wdsacl                         -- Set WDS List
 set aging                          -- Set Aging Interval
 set apmode                         -- Set AP Mode
 set authentication                 -- Set Authentication Type
 set basisconnect                   -- Set Basis of Connect Mode
 set beaconinterval                 -- Modify Beacon Interval
 set bridgelearning                 -- Enable/disable bridge learning
 set burstSeqThreshold              -- Set Max Number of frames in a Burst
 set burstTime                      -- Set Burst Time
 set calibration                    -- Set Calibration Period
 set cckTrigHigh                    -- Set Higher Trigger Threshold for CCK Phy Errors For ANI Control
 set cckTrigLow                     -- Set Lower Trigger Threshold for CCK Phy Errors For ANI Control
 set cckWeakSigThr                  -- Set ANI Parameter for CCK Weak Signal Detection Threshold
 set cipher                         -- Set Cipher
 set countrycode                    -- Set Country Code
 set ctsmode                        -- Set CTS Mode
 set ctsrate                        -- Set CTS Rate
 set ctstype                        -- Set CTS Type
 set dhcpc                          -- Set DHCP Clinet State
 set domainsuffix                   -- Set Domain Name Server Suffix
 set dtim                           -- Set Data Beacon Rate (DTIM)
 set enableANI                      -- Turn Adaptive Noise Immunity Control On/Off
 set encryption                     -- Set Encryption Mode
 set puregmode                      -- Set Pureg Mode
 set eth2wlan                       -- Set Eth2Wlan Broadcast packet filter state
 set factorydefault                 -- Restore to Default Factory Settings
 set firStepLvl                     -- Set ANI Parameter for FirStepLevel
 set  Radio Frequency (MHz)         -- Set Fragment Threshold
 set frequency                      -- Set Radio Frequency (MHz)
 set gateway                        -- Set Gateway IP Address
 set groupkeyupdate                 -- Set Group Key Update Interval (in Seconds)
 set hostipaddr                     -- Set Host IP address
 set ipaddr                         -- Set IP Address
 set ipmask                         -- Set IP Subnet Mask
 set key                            -- Set Encryption Key
 set keyentrymethod                 -- Select Encryption Key Entry Method
 set keysource                      -- Select Source Of Encryption Keys
 set login                          -- Modify Login User Name
 set rbcnt                          -- Reset reboot counter
 set matstate                       -- Set MAT Status
 set syslog                         -- Set sysLog settings
 set nameaddress                    -- Set Name Server IP address
 set noiseImmunityLvl               -- Set ANI Parameter for Noise Immunity Level
 set ofdmTrigHigh                   -- Set Higher Trigger Threshold for OFDM Phy Errors for ANI Control
 set ofdmTrigLow                    -- Set Lower Trigger Threshold for OFDM Phy Errors for ANI Control
 set ofdmWeakSigDet                 -- Set ANI Parameter for OFDM Weak Signal Detection
 set password                       -- Modify Password
 set passphrase                     -- Modify Passphrase
 set quietAckCtsAllow               -- Allow Ack/Cts frames during quiet period
 set quietDuration                  -- Duration of quiet period
 set quietOffset                    -- Offset of quiet period into the beacon period
 set radiusname                     -- Set RADIUS name or IP address
 set radiusport                     -- Set RADIUS port number
 set radiussecret                   -- Set RADIUS shared secret
 set rate                           -- Set Data Rate
 set remoteAP                       -- Set Remote AP's Mac Address
 set hwtxretries                    -- Set HW Transmit Retry Limit
 set swtxretries                    -- Set SW Transmit Retry Limit
 set rtsthreshold                   -- Set RTS/CTS Threshold
 set shortpreamble                  -- Set Short Preamble
 set shortslottime                  -- Set Short Slot Time
 set sntpserver                     -- Set SNTP/NTP Server IP Address
 set softwareretry                  -- Set Software Retry
 set spurImmunityLvl                -- Set ANI Parameter for Spur Immunity Level
 set ssid                           -- Set Service Set ID
 set ssidsuppress                   -- Set SSID Suppress Mode
 set SuperG                         -- Super G Features 
 set systemname                     -- Set Access Point System Name
 set sta2sta                        -- Set wireless STAs to wireless STAs connect state
 set eth2sta                        -- Set ethernet to wireless STAs connect state
 set tzone                          -- Set Time Zone Setting
 set wds                            -- Set WDS Mode
 set wep                            -- Set Encryption Mode
 set wlanstate                      -- Set wlan state
 set wirelessmode                   -- Set Wireless LAN Mode
 set telnet                         -- Set Telnet Mode
 set timeout                        -- Set Telnet Timeout
 tst report                         -- Print tst report
 tst start                          -- Start tst
 tst stop                           -- Stop tst
 timeofday                          -- Display Current Time of Day
 version                            -- Software version
 snmp adduser                       -- Add User To SNMP Agent
 snmp deluser                       -- Delete User From SNMP Agent
 snmp showuser                      -- Show User In SNMP Agent
 snmp setauthkey                    -- Set User Auth Key
 snmp setprivkey                    -- Set User Private Key
 snmp addgroup                      -- Add User Group
 snmp delgroup                      -- Delete User Group
 snmp showgroup                     -- Show User Group
 snmp addview                       -- Add User View
 snmp delview                       -- Delete User View
 snmp showview                      -- Show User View
 snmp addcomm                       -- Add Communication String
 snmp delcomm                       -- Delete Communication String
 snmp showcomm                      -- Show Communication String
 snmp addhost                       -- Add Host To Notify List
 snmp delhost                       -- Delete Host From Notify List
 snmp showhost                      -- Show Host In Notify List
 snmp authtrap                      -- Set Auth Trap Status
 snmp sendtrap                      -- Send Warm Trap
 snmp load_default                  -- Load SNMP Default Setting
 tftp get                           -- Get a file from TFTP Server.
 tftp secget                        -- Securely get a file from TFTP Server.
 tftp uploadtxt                     -- Upload the configuration of the device to TFTP Server.
 tftp secuploadtxt                  -- Securely upload the configuration of the device to TFTP Server.
 tftp srvip                         -- Setup the TFTP Server IP address.
 tftp update                        -- Update the file to the device.
 tftp info                          -- Information about the TFTPC setting.